SmartSafe iSmartLink ST10 with SmartLink "C" VCI Campaign
SmartSafe iSmartLink ST10 with SmartLink "C" VCIPremium Online Programming Diagnostic, Immo & ADAS ToolList Price $4480.00 plus GST Special price $3980.00 plus GST 3 years free updates Options that can be added ADAS for Radar (3-in-1) $6200.00 plus GST IMMO G3 $1395.00 plus GST EV software Activation $698.00 plus GST Osilloscope 2-Channel $780.00 plus GST TTM113 Tyre Tread Depth Examiner $740.00 plus GST ST10, developed by SmartSafe, is a professional Auto Smart Diagnostic Tool that integrates ADAS calibration, anti-theft matching and vehicle diagnosis. The device can perform fault diagnosis of the entire product model and system (including reading/clearing fault codes and reading data streams, etc.), and can be used with the specified ADAS calibration tool (optional) for ADAS calibration.   Get the same online ECU programming coverage as Launch X431 Pad V and IMMO coverage as Launch IMMO PAD with updated hardware at 30% less with FREE HD Trucks coverage Features of iSmartlink D01/ST10:
 ECU Online Programming + ECU Coding iSmartlink D01 automotive scanner is compliant with D-PDU, SAE J2534 & RP1210 to update OEM software, replace the existing software/ firmware in ECU, fix ECU parameters loss, program new ECUs, and fix software-controlled drivability issues. It can do ECU programming for many car brands, including for VW, Ford, Audi, BMW, Land Rover, MG, Mercedes, Nissan, Porsche, Renault, Seat, Subaru and more to come. When you need to do online programming?
 Supported Vehicle Brands12V Passenger CarsAbarth, Acura, Alfa, Audi, BAIC, Bentley, BMW, Bugatti, Buick, BYD, Cadillac, Changan, Chery, Chevrolet, Chrysler, Citroen, Dacia, Daewoo, Daihatsu, Dodge, Ford, Fiat, Foton, GM, GMSA, GWM, Honda, Hyundai, Infiniti, Isuzu, JAC, Jaguar, Jeep, Kia, Lamborghini, Lancia, Land Rover, Lexus, Lincoln, Maserati, Maybach, Mazda Mercedes, MG, Mini, Mitsubishi, Nissan, Opel, Opel South Africa, Peugeot, Porsche, Renault, Seat, Skoda, Smart, Sprinter, Subaru, Suzuki, Tesla, Toyota, Volvo, VW, VW_CV 24V Heavy Duty Trucks and BusesBendix, Benz, DAF, DFL, Detroit, ERF, FAW, Freightliner, Fuso, Eaton, Hino, International, Isuzu, Iveco, Kenworth, Mack, Man, Otokar, Peterbilt, Renault, Scania, Setra, Sisu, Temsa, UD, Volvo, Wabco Wide Range of Maintenance Functions for CarsAir/Fuel Reset This function is applied to set or learn Air/Fuel ratio parameters. Electronic Parking Brake Reset This function enables you to retract the calipers or reset the brake after replacing the brake pads. Oil Reset Service If the service lamp is on, reset the driving mileage or driving time, so as to turn off the service light and enable Steering Angle Calibration Reset the steering angle, after replacing the steering angle position sensor, replacing steering mechanical parts, performing four-wheel alignment. Battery Maintenance System Reset This function enables you to perform a reset on the battery monitoring unit of vehicle battery when the battery is replaced, or the battery monitoring sensor is replaced. ABS Bleeding Perform various bi-directional tests to check the operating conditions of Anti-lock Braking System (ABS) when the ABS contains air or when the ABS ecu or pump, brake cylinder, brake line, or brake fluid is replaced. Throttle Learning Calibrate throttle actuators and return the learned values stored on ECU to the default state after replacement of the ECU or throttle assembly. Tire Pressure Monitor System Reset Look up the tire sensor IDs from the vehicle’s ECU, reset tire pressure and turn off the tire pressure MIL when pressure is too low or tire pressure monitoring device is replaced or installed, or tire is replaced Diesel Particulate Filter (DPF) Regeneration This function enables you to clear PM (Particulate Matter) from the DPF filter through continuous combustion oxidation mode (such as high temperature heating combustion, fuel additive or catalyst reduce PM ignition combustion) to stabilize the filter performance. Gearbox Matching Complete the gearbox self-learning to improve gear shifting quality when the gearbox is disassembled or repaired. Gear Learning This function enables you to perform tooth learning for the car, to turn off the MIL after the engine ECU, crankshaft position sensor, or crankshaft flywheel is replaced, or if Tthe DTC ‘tooth not learned’ is present. Motor Angle Calibration When the rotor position detected by the motor angle position sensor is different from the actual rotor field position, motor angle calibration must be performed. Coolant Bleed Use this function to activate the electronic water pump before venting the cooling system. Engine Power Balance Monitoring It is used to monitor crankshaft acceleration in the power stroke of each cylinder, to determine the relative power provided by each cylinder. IMMO Prog This function supports the reading and writing of car key chip, EEPROM chip, MCU chip, EEPROM and flash of engine ECU and transmission ECU. IMMO Service This function enables you to perform the anti-theft key matching function, so that the immobilizer control system on the car identifies and authorizes remote control keys to normally use the car. High Voltage Battery Diagnosis It is used for high voltage battery diagnosis and status information detection. Gas Particulate Filter Regeneration After the GPF is used for a long time, fuel consumption is increased and engine output power is reduced. In this case, the GPF replacement or regeneration must be performed. Transport Mode In order to reduce power consumption, the following functions may be disabled, including limiting the vehicle speed, not waking up the door opening network, and disabling the remote control key, Tire Reset This function is used to set the size parameters of the modified or replaced tire. Windows Calibration This feature is designed to perform door window matching to recover ECU initial memory, and recover the automatic ascending and descending function of power window. AdBlue Reset After the diesel exhaust treatment fluid (car urea) is replaced or filled up, urea reset operation is required. NOx Sensor Reset NOx sensor is used to detect the NOx content in engine exhaust. If the NOx fault is re-initialized and the NOx catalytic converter is replaced, it is necessary to reset the catalytic converter learned values. Injector Coding This function enables you to write injector actual code or rewrite code in the ECU to the injector code of the corresponding cylinder after the ECU or injector is replaced. Stop/Start Reset This function is used to open or close the automatic start-stop function via setting the hidden function in ECU (provided that the vehicle has a hidden function and supported by hardware). Sunroof Initialization This function enables you to set the sunroof lock off, closed when it rains, sliding / tilting sunroof memory function, temperature threshold outside the car etc. Suspension Calibration A the height of the body when replacing the body height sensor, or control module in the air suspension system and when the vehicle height is incorrect. Language Change This function is used to change the system language of the vehicle central control panel. Intelligent Cruise Control System Diagnosis It is used for matching after the intelligent cruise control module is replaced or repaired. AC System Relearn/Initialization AC system relearn/ initialization must be performed when the vehicle AC ECU or actuator is replaced or the ECU memory is lost. Seats Calibration This function is applied to match the seats with memory function that are replaced and repaired. AFS (Adaptive Front-lighting System) Reset Initialise the adaptive headlamp system. AFS system adjusts headlamp automatically according to the environmental light intensity, monitors the vehicle’s speed and body posture, and adjust the lighting angle. EGR Learning This function is used for learning after EGR (Exhaust Gas Re circulation) valve cleaning or replacement.
What Functions area available on Trucks and Buses?Service Functions for Trucks:
Calibrations on Trucks:
Click to find out more about the ST10 with SmartLink C All prices exclude GST and freight. Conditions apply. To place your order please call 0272321319 or email sales@scanzed.co.nz |
